Top 10 common forklift mishaps ， forklift procedure must focus on these matters ！.

Top 10 common forklift mishaps ， forklift procedure must focus on these matters ！.

Blog Article

Do not underestimate the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are many accidents including forklifts.

Situation 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty items, the workers utilized their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the permitted width of the path and holds on the roadside shelf, which practically causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) scale must be secure before beginning.
3. When the forklift begins with a tons, the driver needs to first validate that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly affect the security of the forklift. .
3. After dumping, the fork ought to be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or automobiles nearby, the driving signal ought to be released initially. High-speed sharp turns are banned. High-speed sharp turns will trigger the automobile to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is restricted to brake suddenly while driving with tons unless there are special conditions.
6. When the forklift is running, it has to obey the traffic rules in the factory and should keep a specific security range from the automobile ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the tons should not block the chauffeur's sight. In special circumstances, when the thing influences the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive throughout the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when going into Stand-on Electric Pallet Stacker the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to stand on the fork to hold things and play a stabilizing role. .
12. If problems are located, they will certainly be repaired and reported in a prompt way, and they will never ever run with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between the two forks need to be changed as needed to make the lots of the two forks well balanced and not manipulated, and one side of the item need to be against the rack. .
2. It is prohibited to work with a solitary fork or utilize a fork top or pull. In unique circumstances, safety and security warning signs must be set up to remind bordering pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the vehicle must be slow-moving and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be kept in mind that the fork tip must not touch various other goods or items. The load must be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to stay clear of the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to make use of forks to lift personnel to participate in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, put, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the parking brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you encounter a person before you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope should be slow-moving and uniform, and no activating the slope is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the vehicle driver's line of sight, they must take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed Electric Forklift Truck for Warehouse to use stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, slim roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844